Posts Tagged ‘Westfield’

Rockaway York Dealer Tip: Causes of Delayed Furnace Ignition

Monday, December 26th, 2011

Delayed ignition is usually accompanied by a loud banging or booming sound that resembles a small explosion in your gas appliance. In your Rockaway home’s York furnace, this can be terrifying and should never be ignored.

What Causes Delayed Ignition

Delayed ignition usually happens when you first turn on your furnace, often after a long delay between use, so usually early in the fall or late in the spring when you don’t necessarily have it on every day of the week.

What happens is moisture builds up over the course of a period of inactivity and begins to corrode the firebox in your furnace. That corrosion builds up to the point that it starts to block the ports that feed gas into the burners. When these ports get blocked, the burners down the line cannot light and when you flip the switch, they won’t light immediately.

Of course, while rust and corrosion are a risk, lint and dust can be equally problematic (and are more common if you don’t have your furnace cleaned properly each fall). Sulfur build up is also a possibility, as it is left behind by burning natural gas. It will appear as a layer of white on the surface of the burners or the pilot light.

When all of this happens and the ports are not cleaned properly, gas will build up in the chamber after it is turned on and, when it finally ignites, create the small boom sound. It doesn’t just sound like an explosion – it is one – and if ignored, it can become incredibly dangerous.

Solving the Problem

Delayed furnace ignition is an easy problem to avoid. All you need to do is have your York furnace cleaned properly before turning it on each fall. A technician will clean the burners and ports and remove any dust, lint, rust or sulfur buildup that might block ignition and cause a delay.

When replacing your York furnace, look for a device with corrosion resistant materials. You can learn more about these when it comes time to replace your furnace from a technician. Most importantly, be careful. It may be a small problem now, but if left to build up over time, that small boom can become a much larger one. If you have any questions about delayed furnace ignition, talk to your New Jersey York Dealer.

Common Furnace Problems: A Guide from Hillside

Monday, November 14th, 2011

When it comes to your Hillside home’s York furnace, you simply want it to work all of the time. But just like any other piece of equipment, your furnace will have problems from time to time. A few of these are relatively simple to fix on your own, but for the most part you’ll need to call in someone to take care of the repairs for you.

However, before you can do that, you’ll need to recognize that a problem exists at all. And the earlier you notice the warning signs, the better off you’ll be. It’s always better to get a furnace problem taken care of right away than to wait until your York furnace stops working completely.

It’s also good to remember that quite often the problems you’re having with your furnace are really originating with your thermostat. This is usually welcome news, as thermostats are much cheaper and easier to repair and replace than many other parts of your furnace. In fact, even if your York furnace isn’t working at all, it may only be the result of a faulty thermostat.

Another problem you may start to notice is that one part of your house is being warmed more than another part. When this happens, it can be a sign that there is something wrong with the furnace, but it may also be that the pressure in your duct system is not balanced properly. A simple rebalancing of this system can have your house heating evenly again in no time.

You may also realize that your furnace seems to be cycling on and off too often. When a furnace is working properly, it will come on for a considerable period of time and then shut off until the temperature in the house drops below the desired level. However, some problems can cause your furnace to complete many short cycles rather than fewer short ones.

If this is happening to your furnace, there are several possible causes. Something might be wrong with the blower on the furnace or the thermostat might not be feeding the furnace the correct information. Another possibility is that your furnace’s air filter is dirty or clogged.

While there are sometimes simple and straightforward solutions to these types of common furnace problems, it’s best to call in a York professional to have them take a look if you’re not sure where to start searching for a problem. In most cases you’ll need them to come out and make the necessary repairs anyway.

Product of the Week: Affinity Series YZH 18 SEER Heat Pump

Wednesday, October 5th, 2011

Heat pumps draw warm air from one environment and place it on another, which can work to both heat and cool a home. This means that heat pumps are a great comfort option, which is why our product of the week is the Affinity Series YZH 18 SEER Heat Pump.  This top-of-the-line York heat pump is extremely energy efficient, with a SEER rating 18, which makes twice as efficient as some older models. To help the environment even more, it uses R-410A refrigerant which does harm the ozone layer (unlike older refrigerants).

And you don’t have to worry about the Affinity Series YZH 18 SEER Heat Pump being too loud, it was designed with the QuietDrive™ System. This York system is specially designed to limit the noise of your heat pump. The Affinity Series YZH 18 SEER Heat Pump is very durable with powder-coated paint to protect it against the elements and sealed electrical contactors.  You won’t find a more reliable heat pump!

For more information about the Affinity Series YZH 18 SEER Heat Pump, check out this brochure. To learn about getting one installed in your home, contact your local York Dealer.